A Step-by-Step Overview to Installing a Bathtub
A Step-by-Step Overview to Installing a Bathtub
Blog Article
The publisher is making a number of great points about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround in general in this great article following next.
Setting up a bathtub isn't exactly brain surgery, but it does call for strong plumbing, carpentry, and sometimes, tiling abilities. Changing an old tub with a new one is also a moderately hard task. If the old bathtub is readily accessible, the task can move quickly; if you have to open up a wall to remove the old bathtub as well as place the brand-new bathtub, the job is much harder. In either instance, the project is within a residence handyman's skills, although you will certainly need an assistant to leave the old bathtub as well as embeded in the new one. Make sure you have actually qualified yourself for the job as well as are comfortable attempting it. Rather than employing a contractor to take control of a halfway-completed project, it is far better to think about employing one before you start. Possibilities are you might need a specialist plumber to make tube connections.
This short article will certainly help you set up a brand-new tub in your bathroom if you have actually currently purchased a brand-new bathtub and do not need to alter the setup of your previous supply of water pipelines.
Your devices and product list should make up the following:
Removing Old Taps
If you need to change old faucets with new ones as a part of your setup, after that the first thing you should do is detach the water system. After doing so, activate the taps to drain any type of water continuing to be in the system. The procedure of removing the existing taps can be rather bothersome as a result of the restricted access that is commonly the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a cloth ready for the staying water that will certainly originate from the pipelines. As soon as the supply pipes have been eliminated, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from turning during this process. When the taps have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any type of old securing substance.
Prior to going on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will need a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end provides a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, place the tap in the installing hole in the bath/basin ensuring that the washers remain in area in between the tap and the sink. Secure the faucet in position with the producer offered backnut. As soon as the faucet is safely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular faucet ports. The former type needs to be attached to the tap ends initially, tightening up just by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Mounting the Bath tub
Using both wood boards under its feet, place the bath tub in the needed position. The wood boards are valuable in evenly spreading out the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto four tiny points.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by examining the level and readjusting the feet on the tub till the spirit level reviews degree.
To mount taps, fit all-time low of the furthest adaptable faucet connector to the ideal supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the water as well as examine all joints as well as brand-new pipework for leaks and also tighten them if required. Load the tub as well as additionally check the overflow outlet and the normal electrical outlet for leakages.
Finally, deal with the bath paneling as explained in the manufacturer's instruction manual. Tiling and also sealing around the tub must wait till the bathtub has actually been made use of at least once as this will certainly settle it into its last position.
Getting ready for the Installment
Firstly, the supporting framework provided with the bath must be fitted (if called for) according to the producer's directions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to make certain that if the faucet features a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the faucets device to stop strain on the bathtub.
Fit the versatile tap ports to the bottom of both faucets using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you make use of all of the supplied washing machines.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath should now be ready to be suited its final setting.
Tiling Around the Bath tub
In the location where the bath satisfies the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to fracture a stiff seal, triggering the water to penetrate the wall surface in between the bath and the tiling, resulting in complications with wetness and also feasible leaks to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your fixtures and fittings. They are offered in tubes as well as cartridges, and can securing gaps up to a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with twists of soaked paper or soft rope. Keep in mind to always fill the bath tub with water prior to sealing, to permit the activity experienced when the tub is in usage. The sealer can break rather very early if you do not think about this motion before securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also conveniently offered on the marketplace. It is a good idea to fit the ceramic tiles using waterproof or waterproof glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am very fascinated with Installing A Bathtub and I am hoping you enjoyed reading the entire page. Enjoyed our blog posting? Please share it. Help others find it. Thanks a lot for taking the time to read it.
Visit Our Website
Report this page